Goto Section: 73.313 | 73.315 | Table of Contents
FCC 73.314
Revised as of October 1, 2008
Goto Year:2007 |
2009
Sec. 73.314 Field strength measurements.
(a) Except as provided for in Sec. 73.209, FM broadcast stations shall not be
protected from any type of interference or propagation effect. Persons
desiring to submit testimony, evidence or data to the Commission for the
purpose of showing that the technical standards contained in this subpart do
not properly reflect the levels of any given type of interference or
propagation effect may do so only in appropriate rule making proceedings
concerning the amendment of such technical standards. Persons making field
strength measurements for formal submission to the Commission in rule making
proceedings, or making such measurements upon the request of the Commission,
shall follow the procedure for making and reporting such measurements
outlined in paragraph (b) of this section. In instances where a showing of
the measured level of a signal prevailing over a specific community is
appropriate, the procedure for making and reporting field strength
measurements for this purpose is set forth in paragraph (c) of this section.
(b) Collection of field strength data for propagation analysis.
(1) Preparation for measurements. (i) On large scale topographic maps, eight
or more radials are drawn from the transmitter location to the maximum
distance at which measurements are to be made, with the angles included
between adjacent radials of approximately equal size. Radials should be
oriented so as to traverse representative types of terrain. The specific
number of radials and their orientation should be such as to accomplish this
objective.
(ii) Each radial is marked, at a point exactly 16 kilometers from the
transmitter and, at greater distances, at successive 3 kilometer intervals.
Where measurements are to be conducted over extremely rugged terrain,
shorter intervals may be used, but all such intervals must be of equal
length. Accessible roads intersecting each radial as nearly as possible at
each 3 kilometer marker are selected. These intersections are the points on
the radial at which measurements are to be made, and are referred to
subsequently as measuring locations. The elevation of each measuring
location should approach the elevation at the corresponding 3 kilometer
marker as nearly as possible.
(2) Measurement procedure. All measurements must be made utilizing a
receiving antenna designed for reception of the horizontally polarized
signal component, elevated 9 meters above the roadbed. At each measuring
location, the following procedure must be used:
(i) The instrument calibration is checked.
(ii) The antenna is elevated to a height of 9 meters.
(iii) The receiving antenna is rotated to determine if the strongest signal
is arriving from the direction of the transmitter.
(iv) The antenna is oriented so that the sector of its response pattern over
which maximum gain is realized is in the direction of the transmitter.
(v) A mobile run of at least 30 meters is made, that is centered on the
intersection of the radial and the road, and the measured field strength is
continuously recorded on a chart recorder over the length of the run.
(vi) The actual measuring location is marked exactly on the topographic map,
and a written record, keyed to the specific location, is made of all factors
which may affect the recorded field, such as topography, height and types of
vegetation, buildings, obstacles, weather, and other local features.
(vii) If, during the test conducted as described in paragraph (b)(2)(iii) of
this section, the strongest signal is found to come from a direction other
than from the transmitter, after the mobile run prescribed in paragraph
(b)(2)(v) of this section is concluded, additional measurements must be made
in a “cluster” of at least five fixed points. At each such point, the field
strengths with the antenna oriented toward the transmitter, and with the
antenna oriented so as to receive the strongest field, are measured and
recorded. Generally, all points should be within 60 meters of the center
point of the mobile run.
(viii) If overhead obstacles preclude a mobile run of at least 30 meters, a
“cluster” of five spot measurements may be made in lieu of this run. The
first measurement in the cluster is identified. Generally, the locations for
other measurements must be within 60 meters of the location of the first.
(3) Method of reporting measurements. A report of measurements to the
Commission shall be submitted in affidavit form, in triplicate, and should
contain the following information:
(i) Tables of field strength measurements, which, for each measuring
location, set forth the following data:
(A) Distance from the transmitting antenna.
(B) Ground elevation at measuring location.
(C) Date, time of day, and weather.
(D) Median field in dBu for 0 dBk, for mobile run or for cluster, as well as
maximum and minimum measured field strengths.
(E) Notes describing each measuring location.
(ii) U.S. Geological Survey topographic maps, on which is shown the exact
location at which each measurement was made. The original plots shall be
made on maps of the largest available scale. Copies may be reduced in size
for convenient submission to the Commission, but not to the extent that
important detail is lost. The original maps shall be made available, if
requested. If a large number of maps is involved, an index map should be
submitted.
(iii) All information necessary to determine the pertinent characteristics
of the transmitting installation, including frequency, geographical
coordinates of antenna site, rated and actual power output of transmitter,
measured transmission line loss, antenna power gain, height of antenna above
ground, above mean sea level, and above average terrain. The effective
radiated power should be computed, and horizontal and vertical plane
patterns of the transmitting antenna should be submitted.
(iv) A list of calibrated equipment used in the field strength survey,
which, for each instrument, specifies its manufacturer, type, serial number
and rated accuracy, and the date of its most recent calibration by the
manufacturer, or by a laboratory. Complete details of any instrument not of
standard manufacture shall be submitted.
(v) A detailed description of the calibration of the measuring equipment,
including field strength meters, measuring antenna, and connecting cable.
(vi) Terrain profiles in each direction in which measurements were made,
drawn on curved earth paper for equivalent 4/3 earth radius, of the largest
available scale.
(c) Collection of field strength data to determine FM broadcast service in
specific communities.
(1) Preparation for measurement. (i) The population (P) of the community,
and its suburbs, if any, is determined by reference to an appropriate
source, e.g., the 1970 U.S. Census tables of population of cities and
urbanized areas.
(ii) The number of locations at which measurements are to be made shall be
at least 15, and shall be approximately equal to 0.1(P)^1/2, if this product
is a number greater than 15.
(iii) A rectangular grid, of such size and shape as to encompass the
boundaries of the community is drawn on an accurate map of the community.
The number of line intersections on the grid included within the boundaries
of the community shall be at least equal to the required number of measuring
locations. The position of each intersection on the community map determines
the location at which a measurement shall be made.
(2) Measurement procedure. All measurements must be made using a receiving
antenna designed for reception of the horizontally polarized signal
component, elevated 9 meters above ground level.
(i) Each measuring location shall be chosen as close as feasible to a point
indicated on the map, as previously prepared, and at as nearly the same
elevation as that point as possible.
(ii) At each measuring location, after equipment calibration and elevation
of the antenna, a check is made to determine whether the strongest signal
arrives from a direction other than from the transmitter.
(iii) At 20 percent or more of the measuring locations, mobile runs, as
described in paragraph (b)(2) of this section shall be made, with no less
than three such mobile runs in any case. The points at which mobile
measurements are made shall be well separated. Spot measurements may be made
at other measuring points.
(iv) Each actual measuring location is marked exactly on the map of the
community, and suitably keyed. A written record shall be maintained,
describing, for each location, factors which may affect the recorded field,
such as the approximate time of measurement, weather, topography, overhead
wiring, heights and types of vegetation, buildings and other structures. The
orientation, with respect to the measuring location shall be indicated of
objects of such shape and size as to be capable of causing shadows or
reflections. If the strongest signal received was found to arrive from a
direction other than that of the transmitter, this fact shall be recorded.
(3) Method of reporting measurements. A report of measurements to the
Commission shall be submitted in affidavit form, in triplicate, and should
contain the following information:
(i) A map of the community showing each actual measuring location,
specifically identifying the points at which mobile runs were made.
(ii) A table keyed to the above map, showing the field strength at each
measuring point, reduced to dBu for the actual effective radiated power of
the station. Weather, date, and time of each measurement shall be indicated.
(iii) Notes describing each measuring location.
(iv) A topographic map of the largest available scale on which are marked
the community and the transmitter site of the station whose signals have
been measured, which includes all areas on or near the direct path of signal
propagation.
(v) Computations of the mean and standard deviation of all measured field
strengths, or a graph on which the distribution of measured field strength
values is plotted.
(vi) A list of calibrated equipment used for the measurements, which for
each instrument, specifies its manufacturer, type, serial number and rated
accuracy, and the date of its most recent calibration by the manufacturer,
or by a laboratory. Complete details of any instrument not of standard
manufacture shall be submitted.
(vii) A detailed description of the procedure employed in the calibration of
the measuring equipment, including field strength meters, measuring antenna,
and connecting cable.
[ 40 FR 27682 , July 1, 1975; 40 FR 28802 , July 9, 1975, as amended at 48 FR 29508 , June 27, 1983]
Goto Section: 73.313 | 73.315
Goto Year: 2007 |
2009
CiteFind - See documents on FCC website that
cite this rule
Want to support this service?
Thanks!
Report errors in
this rule. Since these rules are converted to HTML by machine, it's possible errors have been made. Please
help us improve these rules by clicking the Report FCC Rule Errors link to report an error.
hallikainen.com
Helping make public information public